beccabooo Posted April 4, 2015 Report Share Posted April 4, 2015 Hello All, I recently purchased a 2010 Blissed Millie which included a hydraulic lift. I am in the process of setting up the table, and before I go too far, I would like to know if I have the lift in the correct location. The document I found on the forum said place small bracket 3.5" to left of center tube from panto side, but in the pics I took before it was disassembled, it was like I show in my current setup (on both sides of tubes, but pic is front side of table). Should it be 'centered' between the 2nd and 3rd tubes from panto side? Also, please verify where the black grommets should be located. In one pic, it is below the screw. In the other, it is between the plate and bracket (I think this is right place). Thanks in advance for any help. Looking forward to getting her up and running so I can PPP and join in more on this wonderful forum. Becky Link to comment Share on other sites More sharing options...
barbm Posted April 4, 2015 Report Share Posted April 4, 2015 Becky, I'd have to look it up, but I'm pretty sure the grommet go between the bracket and bar - not next to the screw head. And the location of the module underneath looks fine, as long as none of the hydraulic lines are crimped or over-stretched. You're doing great! Link to comment Share on other sites More sharing options...
beccabooo Posted April 5, 2015 Author Report Share Posted April 5, 2015 Thanks Barb! I'll keep going. Becky Link to comment Share on other sites More sharing options...
barbm Posted April 5, 2015 Report Share Posted April 5, 2015 For those who run into similar problems, here's a recent installation document for the Hydraulic Lift. Hydro lift assembly November 1 2010.pdf Link to comment Share on other sites More sharing options...
Luz2Quilt Posted April 5, 2015 Report Share Posted April 5, 2015 Becky - Congrats on your hydraulic lift - you are going to love it (I do)! I'm sure you'll have it going in no time with the support of APQS or one of the dealers that monitors this forum. Link to comment Share on other sites More sharing options...
beccabooo Posted April 5, 2015 Author Report Share Posted April 5, 2015 Hi Barb, Me again. I moved all the black grommets to be between the bracket and plate and it seems the lift moves from the front to the back of the table. I've tightened the screws are far as they will go. The lift does not slide along the length of the table. Is it supposed to move at all? Becky Link to comment Share on other sites More sharing options...
barbm Posted April 5, 2015 Report Share Posted April 5, 2015 The lift shouldn't move while it's in use, but it can shift a little, usually side to side, if you move it yourself. That's so you can position it optimally for your table length. Take a look at the document I posted above, and if that doesn't answer your questions, I'll check in later tonight. Family's on their way for Easter dinner! Link to comment Share on other sites More sharing options...
beccabooo Posted April 5, 2015 Author Report Share Posted April 5, 2015 Barb, The lift is moving front the front of the table to the back. Enjoy Easter dinner with your family! Becky Link to comment Share on other sites More sharing options...
barbm Posted April 5, 2015 Report Share Posted April 5, 2015 Becky, I'm confused.... Family should be leaving before too awfully long - do you want to call me and we can figure it out? Link to comment Share on other sites More sharing options...
beccabooo Posted April 6, 2015 Author Report Share Posted April 6, 2015 Yes, that would be great if I could call you. PM me your number and time to call, please. Link to comment Share on other sites More sharing options...
barbm Posted April 6, 2015 Report Share Posted April 6, 2015 Becky, you can give me a call anytime tonight (it's just before 6 p.m. here) or during the day tomorrow. (509) 671-1467 Link to comment Share on other sites More sharing options...
beccabooo Posted April 6, 2015 Author Report Share Posted April 6, 2015 Thanks for taking my call and easing my mind, Barb. It's good to know there is a lil 'play' in the lift. NOW, I think I can continue with the setup. You rock! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.