amadarling

Screw won't Secure Machine Needle

Recommended Posts

Hi there - The tiny screw that secures the machine needle will no longer tighten - it just turns and turns, This has happened before and I replaced the screw and it solved the problem. I am now waiting for a new screw to arrive. 

Just wondering if anyone else has experienced this problem? It's strange that it has happened twice now (and frustrating!) - I'm just wondering if its the actual metal threads inside the hole that the screw goes into that may be damaged and not the actual screw its self?

Any advice welcome!

Amanda

Share this post


Link to post
Share on other sites

Amanda,

You can go to your local hardware store, and purchase a 4-20 screw with an allen wrench head.  The allen wrench head screw should be shorter than a normal head screw.  You will need a screw long enough to go through the entire needle bar.

Then using the hole on the opposite side of the hole you normally secure the needle, with your fingers twist the screw in and then through to the hole that is having issues.  If it gets tight and you cannot turn the screw, back it up a little and try again.  You are re-cutting/cleaning up the "threads" in the needle bar.

Remember, when you tighten the screw to secure the needle, you do not need a large screw driver.  Think eye glasses screw driver.  Just finger tight.  When you change needles on your DSM, I hazard to guess you only use your fingers to tighten the screw.  Using this method, I doubt your needle has ever come lose or fallen out while you were sewing.  

If you want a new needle bar screw today, buy a 4-20 nut along with the screw.  Put the nut on the screw, and twist it all the way down to the head.  Then cut the screw off  to match the length of the original APQS screw.  You can use a hacksaw or a Dremel tool with a cutting disk.

Then turn the nut off the screw to clean up the threads that were damaged when you cut the screw length down to size.  Make sure you turn the screw back and forth before you finally remove it from the screw.  Only the end of the screw threads were damaged, so that is the area that needs to be fixed by rotating the nut back and forth.  

If the hole is totally stripped, you can use the hole on the other side to secure the needle.  Remember, only finger tight, so you do not have the same issue with this hole.

https://forum.apqs.com/topic/36523-needle-bar-replacement/?tab=comments#comment-513235

I hope this fixes things for you.

Cagey

 

 


May your threads be balanced, and your bobbin forever full….

Share this post


Link to post
Share on other sites

Good morning Amanda

Going by memory as we sold our machines and retired.  The needle screws are 4-40 and available at your local hardware store.  They will be a little longer and may have a different head.  The screw can be installed on the opposite side of the needle bar if the threads are messed up.  Also the needle bar can be rotated to get the other hole to the right side if needed  but you will have to check the needle bar height before and after.  See the timing instructions.
 

Nigel


Brenda Wells - Green Millie. Sold November 2017
Nigel Wells - Ultimate 1 with Intellistitch & IQ.  Sold January 2019

Share this post


Link to post
Share on other sites

I replaced my needle clamp screw with an Allan head screw long ago.  IMHO a great decision, and I highly recommend it.  Much easier to properly fit an Allan wrench in the socket, than a screw driver in the slot.  You're also much less likely to over torque the screw with the tiny Allan wrench.

I have to disagree with Cagey about "finger tight" needle clamp screw.  On more than one occasion I've had the needle come out while sewing, and I'll assure you I had the screw more than finger tight.  A good snug twist fro the Allan wrench will usually do the trick.  Jim

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...