jimerickson
-
Posts
1,631 -
Joined
-
Last visited
-
Days Won
86
Content Type
Profiles
Forums
Gallery
Posts posted by jimerickson
-
-
Is your needle raised? If the needle is down, it will catch on the bobbin and keep it from coming out. Jim
-
Is the fabric MODA? I've had what looked like pulled thread, but it was the fabric thread "rolling" over exposing the poorly dyed back side. Don't like MODA for that reason. Jim
-
As I think more about it, I have a question. Is the quilt top or back a batik fabric? Due to the usual tight weave, and some of the coloring agents used on this type fabric, stitching can sometimes be a problem. If you are using batik fabric, got to a larger needle, and use sewer's aid, or some other silicon lube for your needle and thread. Good luck. That just might solve your problems. Jim
-
-
Have you read/seen needle height adjustment instructions? Following them, even without the photos, you should be able to get a pretty good adjustment. It sounds like you might have other timing issues as well. Poor needle bar adjustment will generally cause skipped stitches or broken thread. Hitting a needle may have thrown hook timing off as well. Jim
-
Loosen the top tension.
-
I'm a bit late to the conversation, but here's what I suggest. Remove the side cover (the one to the left when facing the machine-not the one with the tension mechanism). This will let you see what you're doing, and keep you from damaging the screw head trying to turn it. Loosen the screw so you can move the needle bar up and down. Snug the screw so it take a little effort to move it, then adjust to where you want it, and finally tighten it down soundly. While you have the side cover off, clean out any thread or dirt that might be trapped, put a drop of oil on the needle bar, and then reassemble. My machine came with a set of fine photos showing how the hook/needle should look when properly adjusted. If you don't have them maybe APQS can send a set. Good luck. Jim
-
Check your encoders. They might have a loose connection, or be dirty. Also make sure they are making solid contact with the surface they roll on. Good luck. Jim
-
No. What you're experiencing is normal. As you roll up the quilt on the take-up roller it takes up space in the "harp". Each pass you make will shorten your "stitching field". Just plan accordingly. If you're stitching a panto, make sure that it is no deeper than the smallest stitching field will be. Probably 2 or 2 1/2 inches less. Good luck. Jim
-
Price and location?
-
I think the Lenni comes with one. Some of the older machines came with a "spoon" foot that didn't lend itself too well to ruler work, so unless you have a "spoon" foot machine, you shouldn't need to replace the foot to do ruler work. Jim
-
Marie: Bigger is always better, unless it doesn't fit the space. I think a 10' frame would serve most folks OK unless they do a lot of king size quilts. Usually even kings have one dimension that's less than 100". You can load the long dimension to the rollers and quilt really long quilts. I'd go ahead with the modification. Jim
-
OK, I've checked, and found a web site where you can buy Schmetz SERV 7 needles: schmetzneedles.com "Long Arm Needles - 135x5 SERV 7 - Schmetz Needles" Jim
-
-
Welcome. Most of the members have abandoned this forum in favor of FB. Too bad. However, there is a lot of really good info archived here. If you have an issue, ask a question. It might take a day or two for a reply now but you'll get one. More likely, your issue will have been discussed sometime in the past. Just search the posts. Jim
-
I use YLI Longarm Professional on top, Bottom line in the bobbin, and also avoid quilting in the "rubber". No special needle consideration. I would question your choice of batting however. Thermor is really low loft. In my experience T shirts turn out better with a lofty batting. Seems to help with the stretchy knit fabrics. Good luck. Jim
-
Ananuk: This is a long shot, but might help. Contact Kasa Engineering, the makers on Intelliquilt. They have assisted with Compuquilter, support after they went out of business, maybe they can help with outdated Statler software. Jim
-
I use my TOWA on the table top.
I don't have a pig tail on my bobbin cases, and don't really see a need for it. My Happy commercial embroidery machine has a pig tail on it's bobbin case which I'm sure helps with sudden direction changes, but those kinds of direction changes are much less frequent with long arm quilting. If you find tension adjustments easier without the using the tail, then don't use it. You could go further and buy a replacement bobbin case without the pig tail. I think the model you need is BC-DBM(1)NBL3. You can find them online. I've bought mine off e-bay. If you shop online, look for bobbin cases made in Japan, not China. The quality control on the Chinese ones are kind of hit and miss. You might get a good one, then again, you might not. I like TOWA, but Koban or Hirise are good. Jim
-
You haven't told us anything about the tension settings you're using. I typically run pretty tight stitches on my machines, and have had thread breakage problems when using Glide. Others here run it all the time with no apparent issues.
If it's not tension, check your thread guides for wear (probably not the problem since your Millie is new). Then check your timing, especially needle bar height adjustment. If all these check out OK, look at your threading of the machine. You may need to reduce the number of holes you use on your pre-tension bar. Also check your hopping foot height adjustment. Good luck. Jim
-
Turning you needle will help with skipped stitches, but not with tension issues. If you're using equal ruler tension in all directions, then I think it's a matter of tension adjustment. The direction you are sewing affects stitch tension by drag on the top thread. e.g. more tension in some directions, less tension in others. With very light tension the direction tension variables become magnified. My suggestion: Tighten your bobbin tension to 200 on you TOWA, then tighten your top tension enough to balance your stitches. With this tighter stitch, the direction tension differences will be a much smaller percent of total tension, and stitch balance will be easier to achieve. Jim
- Rebecca Grace and MaddieND
-
2
-
I made my own for my Ult2, so I don't know for sure, but I think one offered for a Lenni would fit since they are both built on the same platform. Jim
-
Not too unusual. Especially if you sew in the printed on material. Additional drag on thread inhibits the loop formation which causes skipped stitches. Try a bit of silicon on thread and needle. That will probably help. Good luck. Jim
-
Cagey: Are you sure the needle doesn't hit the center? Take a piece of paper, set it under the hopping foot, pencil around the outside, then turn the needle down til it pierces the paper, remove the paper and measure the distance from the hole to the circle to see just where the foot sets. I don't know anything about the APQS ruler feet, but I do know the way you look at something, sometimes leaves you with an incorrect impression. As much "flap" as there has been about front and back spacing, I'd be surprised if the new feet weren't accurate. Jim
-
What you quilted is probably why the needle went dull. If you still have the worn out needle, check the tip for damage. Run your fingernail up and down the point feeling for a burr. If you feel one, the needle was damaged by hitting something. If there is no burr, it's just dull.
I've heard the story about the chrome vs titanium needle and damage. In my experience, and I've used both type MR needles, there's nothing to it. They both bend and break the same way. Use titanium if you want them to last longer, replace them more often if you don't. I don't think you would have had a bad needle. The Groz-Beckert are high quality needles, and I don't think their quality control would let bad needles leave the factory. Jim
Is My Towa Gauge Working Correctly?
in Gone Quilting...Chat About Anything
Posted
I don't use magnetic bobbins, so I don't have any first hand knowledge, but I'd guess the needle "jumping" might be the magnet releasing and then re-setting. Maybe OK. If you have another bobbin case, try and check with it to see if it also happens. Before you do anything, try another bobbin. When I buy bobbins I always wind some thread on them, pull them through the TOWA, and if I don't get a steady reading, I discard the bobbin as defective. You might have some bad pre-wound bobbins. Good luck. Jim